Add programmers file

programmers.txt

@@ -0,0 +1,130 @@
+avrisp.name=AVR ISP
+avrisp.communication=serial
+avrisp.protocol=stk500v1
+avrisp.program.protocol=stk500v1
+avrisp.program.tool=avrdude
+avrisp.program.tool.default=avrdude
+avrisp.program.extra_params=-P{serial.port}
+
+avrispmkii.name=AVRISP mkII
+avrispmkii.communication=usb
+avrispmkii.protocol=stk500v2
+avrispmkii.program.protocol=stk500v2
+avrispmkii.program.tool=avrdude
+avrispmkii.program.tool.default=avrdude
+avrispmkii.program.extra_params=-Pusb
+
+usbtinyisp.name=USBtinyISP
+usbtinyisp.protocol=usbtiny
+usbtinyisp.program.tool=avrdude
+usbtinyisp.program.tool.default=avrdude
+usbtinyisp.program.extra_params=
+
+arduinoisp.name=ArduinoISP
+arduinoisp.protocol=arduinoisp
+arduinoisp.program.tool=avrdude
+arduinoisp.program.tool.default=avrdude
+arduinoisp.program.extra_params=
+
+arduinoisporg.name=ArduinoISP.org
+arduinoisporg.protocol=arduinoisporg
+arduinoisporg.program.tool=avrdude
+arduinoisporg.program.tool.default=avrdude
+arduinoisporg.program.extra_params=
+
+usbasp.name=USBasp
+usbasp.communication=usb
+usbasp.protocol=usbasp
+usbasp.program.protocol=usbasp
+usbasp.program.tool=avrdude
+usbasp.program.tool.default=avrdude
+usbasp.program.extra_params=-Pusb
+
+parallel.name=Parallel Programmer
+parallel.protocol=dapa
+parallel.force=true
+# parallel.delay=200
+parallel.program.tool=avrdude
+parallel.program.tool.default=avrdude
+parallel.program.extra_params=-F
+
+arduinoasisp.name=Arduino as ISP
+arduinoasisp.communication=serial
+arduinoasisp.protocol=stk500v1
+arduinoasisp.speed=19200
+arduinoasisp.program.protocol=stk500v1
+arduinoasisp.program.speed=19200
+arduinoasisp.program.tool=avrdude
+arduinoasisp.program.tool.default=avrdude
+arduinoasisp.program.extra_params=-P{serial.port} -b{program.speed}
+
+arduinoasispatmega32u4.name=Arduino as ISP (ATmega32U4)
+arduinoasispatmega32u4.communication=serial
+arduinoasispatmega32u4.protocol=arduino
+arduinoasispatmega32u4.speed=19200
+arduinoasispatmega32u4.program.protocol=arduino
+arduinoasispatmega32u4.program.speed=19200
+arduinoasispatmega32u4.program.tool=avrdude
+arduinoasispatmega32u4.program.tool.default=avrdude
+arduinoasispatmega32u4.program.extra_params=-P{serial.port} -b{program.speed}
+
+usbGemma.name=Arduino Gemma
+usbGemma.protocol=arduinogemma
+usbGemma.program.tool=avrdude
+usbGemma.program.tool.default=avrdude
+usbGemma.program.extra_params=
+usbGemma.config.path={runtime.platform.path}/bootloaders/gemma/avrdude.conf
+
+## Notes about Dangerous Prototypes Bus Pirate as ISP
+## Bus Pirate V3 need Firmware v5.10 or later
+## Bus Pirate V4 need Firmware v6.3-r2151 or later
+## Could happen that BP does not have enough current to power an Arduino board 
+## through the ICSP connector. In this case disconnect the +Vcc from ICSP connector
+## and power Arduino board in the normal way.
+buspirate.name=BusPirate as ISP
+buspirate.communication=serial
+buspirate.protocol=buspirate
+buspirate.program.protocol=buspirate
+buspirate.program.tool=avrdude
+buspirate.program.tool.default=avrdude
+buspirate.program.extra_params=-P{serial.port}
+
+# STK500 firmware version v1 and v2 use different serial protocols.
+# Using the 'stk500' protocol tells avrdude to try and autodetect the
+# firmware version. If this leads to problems, we might need to add
+# stk500v1 and stk500v2 entries to allow explicitly selecting the
+# firmware version.
+stk500.name=Atmel STK500 development board
+stk500.communication=serial
+stk500.protocol=stk500
+stk500.program.protocol=stk500
+stk500.program.tool=avrdude
+stk500.program.tool.default=avrdude
+stk500.program.extra_params=-P{serial.port}
+
+jtag3isp.name=Atmel JTAGICE3 (ISP mode)
+jtag3isp.communication=usb
+jtag3isp.protocol=jtag3isp
+jtag3isp.program.protocol=jtag3isp
+jtag3isp.program.tool=avrdude
+jtag3isp.program.tool.default=avrdude
+jtag3isp.program.extra_params=
+
+jtag3.name=Atmel JTAGICE3 (JTAG mode)
+jtag3.communication=usb
+jtag3.protocol=jtag3
+jtag3.program.protocol=jtag3
+jtag3.program.tool=avrdude
+jtag3.program.tool.default=avrdude
+# Set a bitclock of 0.1us (the fastest supported value). This should
+# work regardless of the crystal used, since JTAG doesn't use the MCU
+# clock but dictates its own clock.
+jtag3.program.extra_params=-B0.1
+
+atmel_ice.name=Atmel-ICE (AVR)
+atmel_ice.communication=usb
+atmel_ice.protocol=atmelice_isp
+atmel_ice.program.protocol=atmelice_isp
+atmel_ice.program.tool=avrdude
+atmel_ice.program.tool.default=avrdude
+atmel_ice.program.extra_params=-Pusb